--- title: "PU vs PE Tubing: Pressure, Bend Radius & Use" canonical: "https://yuannaitube.com/polyurethane-vs-polyethylene-tubing/" language: "en-US" --- RESOURCES # PU vs PE Tubing: Pressure, Bend Radius & Use By [YUANNAI TUBE]() Published 2026-11-08Updated 2026-11-08 ![Coils of blue polyurethane tubing and milky-white polyethylene tubing side by side]() **Polyurethane (PU) tubing and polyethylene (PE) tubing** are both sold in coils for air lines, and in the sizes we make they share the same outside and inside diameters. What differs is how much pressure they carry, how tightly they bend and the temperature range they are listed for. This comparison uses our own model tables for both ranges, so you can choose from the numbers. **Quick answer.** In the ten metric sizes we make in both materials, PU carries the same or a higher **working pressure** in nine and bends to a smaller radius in all ten; for example 8 bar versus 6 bar and 10 mm versus 20 mm on the 4 × 2.5 tube. PU is listed for −20 °C to +55 °C in compressed-air, inert-gas and vacuum service; PE is listed for ambient-temperature water and compressed air, with −10 °C to +50 °C in air service. ## Same sizes, different ratings Ten metric model codes exist in both ranges with identical dimensions and the same ±0.10 mm tolerance, so a direct comparison is possible. Every figure comes from our own published model tables, stated at 23 °C. **Working pressure** is the design rating; **bend radius** is the smallest radius the tube is listed for. | Model (same size) | YN-PU working pressure | YN-PE working pressure | YN-PU min. bend | YN-PE min. bend | | --- | --- | --- | --- | --- | | 0425 (4×2.5) | 8 bar | 6 bar | 10 mm | 20 mm | | 0640 (6×4) | 8 bar | 6 bar | 15 mm | 30 mm | | 0850 (8×5) | 7 bar | 7 bar | 20 mm | 40 mm | | 0855 (8×5.5) | 6 bar | 5 bar | 22 mm | 45 mm | | 0860 (8×6) | 5 bar | 6 bar | 25 mm | 50 mm | | 1065 (10×6.5) | 7 bar | 6 bar | 25 mm | 50 mm | | 1080 (10×8) | 6 bar | 4 bar | 30 mm | 75 mm | | 1280 (12×8) | 7 bar | 5 bar | 50 mm | 60 mm | | 1410 (14×10) | 7 bar | 5 bar | 70 mm | 80 mm | | 1612 (16×12) | 7 bar | 3 bar | 95 mm | 110 mm | Two rows do not follow the general pattern. On the 8 × 5 tube the two ratings are equal, and on the 8 × 6 tube the PE rating is the higher one. Read the row for your own model rather than the trend. The full tables, including burst pressure, are on the [PU tubing page]() and the [PE tubing page]() . Fractional sizes differ between the two ranges (PU lists 1/8″, 1/4″, 3/8″, 1/2″ and 3/4″; PE stops at 1/2″), so compare those sizes from the model tables. For every size in one place, see the [tubing size chart]() . ![Blue tubing bent into a tight U-shape beside milky-white tubing bent into a wider curve]() Fig. 1: Illustration of the bend behavior listed in the table: PU (left) bends to a tighter radius than PE (right) at the same size. Illustrative image, not a product photograph. ## Temperature and media - **PU:** listed for −20 °C to +55 °C, for compressed air, inert gases and vacuum circuits. Liquid lubricating oil lines are reviewed against your requirements. - **PE:** listed for ambient-temperature water and compressed air. The air-service range is −10 °C to +50 °C; the water-service range is 0 °C to +55 °C, and freezing is not permitted. Pressure and temperature ratings are listed separately on the data sheets, so check the **working pressure** at your **operating temperature**; see [working pressure and temperature]() . ## Material properties on the data sheets The two data sheets state their properties on different bases, so the figures should not be set side by side as a ranking. | Property | PU (YN-PU) | PE (YN-PE) | | --- | --- | --- | | Hardness | 98 ± 2 Shore A | Not stated on the data sheet | | Tensile strength | ≥ 42 MPa | Approx. 10 MPa at yield, approx. 16 MPa at break | | Elongation at break | ≥ 480% | Approx. 750% | | Other stated values | Tear strength ≥ 115 kN/m; abrasion volume loss ≤ 30 mm³ | Density approx. 0.920 g/cm³; melt mass-flow rate approx. 2.0 g/10 min | The PU values are stated as limits (≥, ≤) and the PE values as approximate typical values. For hardness on a Shore scale, see how to write it into a specification in [how to specify tubing]() . ## Colors and packaging PU standard colors are clear, transparent blue and transparent red, plus solid orange, dark blue, sky blue, black, green and yellow, supplied on engineering-plastic reels or in color boxes. PE standard colors are milky white, dark blue, black, green and yellow (custom colors available), supplied in stretch-film wrapping. Both can carry meter-marked printing, your brand logo and model identification. ## How to choose in four checks 1. **Medium.** Compressed air, inert gas or vacuum: both ranges are listed for air. Water at ambient temperature: the PE data sheet lists it; the PU data sheet does not. 2. **Temperature.** Below −10 °C or above +50 °C in air service, check the PU range first. 3. **Pressure.** Read the **working pressure** for your exact model in each table; the ranges overlap and the order is not the same in every size. 4. **Routing.** Tight bends and moving parts point to the smaller **bend radius**, which is PU in all ten shared sizes. For a hot-water application where standard PE was not enough, see the [PE-RT dishwasher tubing case]() . If the choice is between two PU grades, see [polyether vs polyester PU tubing]() ; for the wider PE range, the [PE tubing guide]() ; for the full picture of materials, [the pneumatic tubing guide]() . For quotation details, send the size, length, quantity, medium and temperature range; the [quotation checklist]() lists every field. ## PU vs PE tubing FAQ What is the difference between PU and PE tubing? In our model tables, the two share the same ten metric sizes, but PU is listed for −20 °C to +55 °C in air, inert-gas and vacuum service and bends to a smaller radius, while PE is listed for ambient-temperature water and compressed air. Is PU or PE tubing better for compressed air? Both are listed for compressed air. For the same size, PU is listed at the same or a higher **working pressure** in nine of the ten shared metric sizes and with a tighter **bend radius** in all ten. Check the row for your model. Can PE tubing be used for water? The PE data sheet lists ambient-temperature water service from 0 °C to +55 °C, and freezing is not permitted. The PU data sheet scope covers compressed air, inert gases and vacuum circuits. Which one bends more tightly? PU, in every size the two ranges share. The 4 × 2.5 tube is listed at 10 mm for PU and 20 mm for PE. Do PU and PE tubing fit the same push-in fittings? Push-in fittings grip the tube outside diameter, and the ten shared sizes have the same OD in both materials. Confirm the fitting against the supplied tolerance; see [matching tubing to fittings]() . ## Sources and scope - [PU Tubing — English data sheet (v3-20261020)]() - [PE Tubing — English data sheet (v1-20261021)]() Use these documents for the identified product models and stated test conditions. The comparison covers YUANNAI TUBE YN-PU and YN-PE models only and does not describe other manufacturers’ PU or **PE tubing**. Confirm the exact model, medium, temperature and pressure before ordering. Content review: [zhangkexin]() · Marketing Review scope: market information and document references. ## Tell us what your application needs. Send your dimensions, operating conditions and quantity. Let’s identify the right tubing for your project. [Request a Quote →]() ## Related tubing products ![Multi-Lumen Tubing]() [Specialty]() ### Multi-Lumen Tubing Custom multi-lumen (multi-bore, multi-core) tubing: twin and multi-line parallel lines for equipment integration. Lumen count, sizes, material and construction are agreed per drawing or sample. [View details →]() ![Antistatic PU Tubing]() [Specialty]() ### Antistatic PU Tubing Custom antistatic (static-dissipative) PU tubing for air and fluid lines near electronics. Resistance range, size and compound are agreed per project and confirmed on samples. [View details →]() ![Flame-Retardant Tubing]() [Specialty]() ### Flame-Retardant Tubing Flame-retardant tubing for air lines. 5 models from 2.5 x 4 mm to 8 x 12 mm. State the fire-performance standard your project requires. [View details →]() ![High-Pressure Composite Tubing]() [Composite]() ### High-Pressure Composite Tubing High-pressure composite tubing for pneumatic, lubrication, spraying and fluid-transfer lines. 28 models: V8 (PU + PA12) and V9 (polyether TPU + PA12). [View details →]()